Update support

[network]
#hostname string of 32 chars max
hostname = myesp

#radio mode bt, wifi-sta, wifi-ap, eth-sta, off
radio_mode = wifi-sta 

#station fallback mode bt, wifi-ap, off
sta_fallback  = wifi-ap

#active when boot device or not  yes / no
radio_enabled = yes

#sta ssid string of 32 chars max 
sta_ssid = myssid

#sta password string of 64 chars max, minimum  0 or 8 chars 
sta_password = *******

#sta ip mode dhcp / static
sta_ip_mode = dhcp

#sta static ip
sta_ip = 192.168.0.2

#sta static gateway
sta_gw = 192.168.0.1

#sta static mask
sta_msk = 255.255.255.0

#sta static dns
sta_dns = 192.168.0.1

#ap ssid string of 32 chars max 
ap_ssid = myssid

#ap password string of 64 chars max, minimum  0 or 8 chars
ap_password = 12345678

#ap static ip
ap_ip = 192.168.0.1

#ap channel 1~14
ap_channel = 11

[services] 
#active or not serial bridge yes / no
serial_bridge_active = yes

# serial bridge baudrate
serial_bridge_baud = 115200

#active or not http yes / no
http_active = yes

#http port
http_port = 80

#active or not telnet yes / no
telnet_active = yes

#telnet port
telnet_port = 23

#active or not websocket yes / no
websocket_active = yes

#websocket port
websocket_port = 8282

#active or not webdav yes / no
webdav_active = yes

#websocket port
webdav_port = 8282

#active or not ftp yes / no
ftp_active = yes

#ftp control port
ftp_control_port = 21

#ftp active port
ftp_active_port = 20

#ftp passive port
ftp_passive_port = 55600

#auto notification
autonotification = yes

#notification type none / pushover / line / email / telegram /ifttt
notif_type = none 

#notification token 1 string of 64 chars max
notif_token1 = 

#notification token 2 string of 64 chars max
notif_token2 = 

#notification settings string of 127 chars max
notif_token_settings= 

#sd card speed factor 1 2 4 6 8 16 32
sd_speed = 4

#check update from sd yes / no
check_for_update = yes

#enable buzzer yes / no
active_buzzer = yes

#active internet time yes / no
active_internet_time = yes

#time servers string of 127 chars max
time_server1 = 1.pool.ntp.org
time_server2 = 2.pool.ntp.org
time_server3 = 3.pool.ntp.org

#time zone -12~12
time_zone = 2
#is dst yes/no
time_dst = no

#authentication passwords string of 20 chars max
admin_password = xxxxxxx
user_password = xxxxxxx
#session time out in min
sesion_timeout = 3

#sensor type if enabled none / dht11 / dht22 / analog / bmp280 / bme280
sensor_type = none
#sensor poiling interval in ms
sensor_interval = 30000


[system]
#target firmware marlin / repetier / marlinkimbra / smoothieware / grbl
targetfw=marlin

#baud rate
baud_rate = 115200

#boot delay in ms
boot_delay = 5000

#boot verbose yes / no
boot_verbose = no

#outputs
#printer screen yes / no
active_remote_screen = yes
#esp3d screen yes / no
active_esp3d_screen = yes
#esp3d serial yes / no
active_serial = yes
#serial bridge yes / no
active_serial_bridge = yes
#websocket yes / no
active_websocket = yes
#telnet yes / no
active_telnet = yes
#bluetooth yes / no
active_bt = yes