[ESP800]

Get fw capabilities eventually set time with pc time and set setup state

Input

[ESP800]<time=YYYY-MM-DDTHH:mm:ss> <version=3.0.0-a11> <setup=0/1> json=<no> pwd=<admin password>

* json=yes
the output format
* time=
to set ESP3D time using ISO 8601 format : `YYYY`-`MM`-`DD`T`HH`:`minutes`:`seconds`
* tz=+08:00 (optional)
to set ESP3D time zone using ISO 8601 format : `+`/`-` `HH`-`minutes`
* version
version of webUI
* setup flag
Enable / Disable the setup flag

Output

  • In json format
{
   "cmd":"800",
   "status":"ok",
   "data":{
           "FWVersion":"bugfix-2.0.x-3.0.0.a200",
           "FWTarget":"marlin",
           "FWTargetID":"30",
           "Setup":"Enabled",
           "SDConnection":"shared",
           "SerialProtocol":"Socket",
           "Authentication":"Disabled",
           "WebCommunication":"Synchronous",
           "WebSocketIP":"192.168.2.117",
           "WebSocketPort":"81",
           "Hostname":"esp3d",
           "WiFiMode":"STA",
           "WebUpdate":"Enabled",
           "FlashFileSystem":"LittleFS",
           "HostPath":"www",
           "Time":"none"
           }
}

  • cmd Id of requested command, should be 800

  • status status of command, should be ok

  • data content of response:

    • FWVersion Version of ESP3D firmware or targeted FW (Marlin with ESP3DLib / grblHal)

    • FWTarget name of targeted Firmware

    • FWTargetID numerical ID of targeted FW as same name can have several Ids

    • Setup Should be Enabled or Disabled according flag in EEPROM/Preferences, this allows to WedUI to start wizard automaticaly (or not)

    • SDConnection This is SD capability, SD can be

      • shared ESP does share access to SD card reader with main board or Firmware (Marlin with ESP3Dlib, ESP3D with hardware SD share solution)
      • direct ESP does have direct access to SD card reader (e.g: ESP3D, grblHal)
      • none ESP does not have direct access to SD card reader, (e.g: ESP3D with only serial connection)

    • SerialProtocol It define how ESP3D FW communicate with main FW

      • Socket ESP and main FW use same FW (e.g: Marlin with ESP3DLib, grblHal)
      • Raw Classic serial connection
      • MKS Serial connection using MKS protocol

    • Authentication Can be Enabled or Disabled

    • WebCommunication currently only Synchronous, because Asychronous has been put in hold

    • WebSocketIP Ip address for the websocket terminal 192.168.2.117

    • WebSocketPort Port for the web socket terminal 81

    • Hostname Hostname of ESP3D or main Baord esp3d

    • WiFiMode Current wiFi mode in use can be AP or STA

    • WebUpdate Inform webUI the feature is available or not, can be Enabled or Disabled

    • FlashFileSystem (currently FileSystem, to be updated soon ) The file system used by ESP board can be LittleFS, SPIFFS, Fat, none

    • HostPath Path where the preferences.json and index.html.gz are stored and can be updated (e.g: www)

    • Time Type of time support

      • none Time is not supported
      • Auto Board use internet to sync time and it is successful
      • Failed to set Board use internet to sync time and it is failed
      • Manual Board use time of ESP800 to set the time and it is successful
      • Not set Board use time of ESP800 to set the time and command did not sent it (time may have been set by previous command)

    • CameraID if ESP has camera it contain the camera ID

    • CameraName if ESP has camera it contain the camera name

    • Axisletters Currently only used for grbHAL can be :

      • XYZABC
      • XYZUVZ (supported soon)
      • XYZABCUVZ (supported soon)