Get fw capabilities eventually set time with pc time and set setup state

Input

[ESP800]<time=YYYY-MM-DDTHH:mm:ss> <version=3.0.0-a11> <setup=0/1> json=<no> pwd=<admin password>

* json=yes
the output format
* time=
to set ESP3D time using ISO 8601 format : `YYYY`-`MM`-`DD`T`HH`:`minutes`:`seconds`
* tz=+08:00 (optional)
to set ESP3D time zone using ISO 8601 format : `+`/`-` `HH`-`minutes`
* version
version of webUI
* setup flag
Enable / Disable the setup flag

Output

• In json format

{
   "cmd":"800",
   "status":"ok",
   "data":{
           "FWVersion":"bugfix-2.0.x-3.0.0.a200",
           "FWTarget":"marlin",
           "FWTargetID":"30",
           "Setup":"Enabled",
           "SDConnection":"shared",
           "SerialProtocol":"Socket",
           "Authentication":"Disabled",
           "WebCommunication":"Synchronous",
           "WebSocketIP":"192.168.2.117",
           "WebSocketPort":"81",
           "Hostname":"esp3d",
           "WiFiMode":"STA",
           "WebUpdate":"Enabled",
           "FlashFileSystem":"LittleFS",
           "HostPath":"www",
           "Time":"none"
           }
}

• cmd Id of requested command, should be 800

• status status of command, should be ok

• data content of response:

  • FWVersion Version of ESP3D firmware or targeted FW (Marlin with ESP3DLib / grblHal)
  • FWTarget name of targeted Firmware
  • FWTargetID numerical ID of targeted FW as same name can have several Ids

  • Setup Should be Enabled or Disabled according flag in EEPROM/Preferences, this allows to WedUI to start wizard automaticaly (or not)

  • SDConnection This is SD capability, SD can be

    • shared ESP does share access to SD card reader with main board or Firmware (Marlin with ESP3Dlib, ESP3D with hardware SD share solution)
    • direct ESP does have direct access to SD card reader (e.g: ESP3D, grblHal)
    • none ESP does not have direct access to SD card reader, (e.g: ESP3D with only serial connection)
  • SerialProtocol It define how ESP3D FW communicate with main FW
  • Socket ESP and main FW use same FW (e.g: Marlin with ESP3DLib, grblHal)
  • Raw Classic serial connection
  • MKS Serial connection using MKS protocol
  • Authentication Can be Enabled or Disabled
  • WebCommunication currently only Synchronous, because Asychronous has been put in hold
  • WebSocketIP Ip address for the websocket terminal 192.168.2.117
  • WebSocketPort Port for the web socket terminal 81
  • Hostname Hostname of ESP3D or main Baord esp3d
  • WiFiMode Current wiFi mode in use can be AP or STA
  • WebUpdate Inform webUI the feature is available or not, can be Enabled or Disabled
  • FlashFileSystem (currently FileSystem, to be updated soon ) The file system used by ESP board can be LittleFS, SPIFFS, Fat, none
  • HostPath Path where the preferences.json and index.html.gz are stored and can be updated (e.g: www)
  • Time Type of time support
    • none Time is not supported
    • Auto Board use internet to sync time and it is successful
    • Failed to set Board use internet to sync time and it is failed
    • Manual Board use time of ESP800 to set the time and it is successful
    • Not set Board use time of ESP800 to set the time and command did not sent it (time may have been set by previous command)
  • CameraID if ESP has camera it contain the camera ID
  • CameraName if ESP has camera it contain the camera name
  • Axisletters Currently only used for grbHAL can be :
  • XYZABC
  • XYZUVZ (supported soon)
  • XYZABCUVZ (supported soon)