Open esp3d/configuration.h and set the features you want.
/* Setup station as default, use AP mode first if not done* Note: need both defined to enable it* Uncomment and edit them to define*///#define STATION_WIFI_SSID "*********"//#define STATION_WIFI_PASSWORD "*********"
/* You can also use a different config file for SSID/password* Just save it in same location as this configuration.h* This file is ignored by github*/#if defined __has_include# if __has_include ("myconfig.h")# include "myconfig.h"# endif#endif/************************************** Serial Communications** Settings and protocols*************************************/
/* Serial Communication protocol* RAW_SERIAL // Basic serial protocol, without data change* MKS_SERIAL // This is a MakerBase communication protocol, used with MKS printers and TFT, it encapsulated data in a custom protocol*/#define COMMUNICATION_PROTOCOL RAW_SERIAL
/* Main Serial port* which serial ESP use to communicate to printer (ESP32 has 3 serials available, ESP8266 only 2)* USE_SERIAL_0 //for ESP8266/32, also used by bootloader output, so consider to make it quiet* USE_SERIAL_1 //for ESP8266/32* USE_SERIAL_2 //for ESP32 Only*///Main serial port#define ESP_SERIAL_OUTPUT USE_SERIAL_0
/* Bridge Serial port (deprecated on esp8266 as second serial is)* which serial ESP use to bridge to another device (ESP32 has 3 serials available, ESP8266 only 2)* USE_SERIAL_0 //for ESP8266/32, also used by bootloader output, so consider to make it quiet* USE_SERIAL_1 //for ESP8266/32* USE_SERIAL_2 //for ESP32 Only\* Comment if not used*///#define ESP_SERIAL_BRIDGE_OUTPUT USE_SERIAL_1
/* Serial buffer size* Maximum size of the serial buffer*/#define SERIAL_RX_BUFFER_SIZE 512/************************************** Target firmware** Targeted firmware that ESP3D will communicate with*************************************//* Target firmware (default UNKNOWN_FW can be changed later in settings)* UNKNOWN_FW* GRBL* MARLIN* SMOOTHIEWARE* REPETIER*/#define DEFAULT_FW UNKNOWN_FW/************************************** Radio mode of ESP3D** The radio mode ESP3D communicate with the network*************************************/
/* Use WiFi* Enable wifi communications*/#define WIFI_FEATURE
/* Use Ethernet* Enable ethernet communications*///#define ETH_FEATURE
//Ethernet type (Check ETH.h eth_phy_type_t)//TYPE_ETH_PHY_LAN8720//TYPE_ETH_PHY_TLK110//TYPE_ETH_PHY_RTL8201//TYPE_ETH_PHY_DP83848//TYPE_ETH_PHY_DM9051//TYPE_ETH_PHY_KSZ8041//TYPE_ETH_PHY_KSZ8081#define ESP3D_ETH_PHY_TYPE TYPE_ETH_PHY_LAN8720
//Ethernet board Clock mode// MODE_ETH_CLOCK_GPIO0_IN// MODE_ETH_CLOCK_GPIO0_OUT// MODE_ETH_CLOCK_GPIO16_OUT// MODE_ETH_CLOCK_GPIO17_OUT#define ESP3D_ETH_CLK_MODE MODE_ETH_CLOCK_GPIO17_OUT
//Pins of ethernet board#define ESP3D_ETH_PHY_POWER_PIN 12//#define ESP3D_ETH_PHY_MDC_PIN 23//#define ESP3D_ETH_PHY_MDIO_PIN 18
//Address of ethernet board//#define ESP3D_ETH_PHY_ADDR 0
/* Use Bluetooth* Enable serial bluetooth communications*///#define BLUETOOTH_FEATURE/************************************** Channels of ESP3D** The way ESP3D communicate*************************************/
/* Use Web server* Enable http server*/#define HTTP_FEATURE
/* Use telnet server* Enable telnet light (raw tcp) communications*/#define TELNET_FEATURE
/* Use Websocket server* Enable websocket communications*///#define WS_DATA_FEATURE
// Enable notifications// Allows to send notifications to the user#define NOTIFICATION_FEATURE
/* Notification message when online* The message that will be sent when the ESP is online*/#define NOTIFICATION_ESP_ONLINE "Hi, %ESP_NAME% is now online at %ESP_IP%"
/* Notification title message* The title of notification*/#define ESP_NOTIFICATION_TITLE "ESP3D Notification"/************************************** Discovery methods of ESP3D** The discovery methods of ESP3D*************************************/
/* Use captive portal* Enable captive portal in AP mode*/#define CAPTIVE_PORTAL_FEATURE
/* Use mDNS discovery* This method need `bonjour` protocol on windows, or `avahi` on linux*/#define MDNS_FEATURE
/* Use Simple Service Discovery Protocol* It is supported on Windows out of the box*/#define SSDP_FEATURE
/************************************** SSDP Customization settings** Customize your ESP3D*************************************/
/* Model name* Modele name of device*/#define ESP_MODEL_NAME "ESP Board"
/* Model number* Modele number of device*/#define ESP_MODEL_NUMBER "ESP3D 3.0"
/* Model url* Modele url of device*/#define ESP_MODEL_URL "https://www.espressif.com/en/products/devkits"
/* Manufacturer name* Manufacturer name of device*/#define ESP_MANUFACTURER_NAME "Espressif Systems"
/* Manufacturer url* Manufacturer url of device*/#define ESP_MANUFACTURER_URL "https://www.espressif.com"/************************************** Flash filesystem** Filesystem on flash*************************************/
/* File system type used by ESP3D* Type of file system used by ESP3D to store files* ESP_SPIFFS_FILESYSTEM (Deprecated)* ESP_FAT_FILESYSTEM (ESP32 only with large partitions)* ESP_LITTLEFS_FILESYSTEM (Default)*/#define FILESYSTEM_FEATURE ESP_LITTLEFS_FILESYSTEM
/* Enable date/time on files* Set date/time on files using SNTP or last webui connection*///#define FILESYSTEM_TIMESTAMP_FEATURE/************************************** SD filesystem** Filesystem on SD card*************************************/
/* SD card connection* ESP_NO_SD //(default)* ESP_NOT_SHARED_SD //Only your ESP board is connected to SDCard* ESP_SHARED_SD //Printer SD Card is also connected to ESP3D* Does your system has SD card and how it is connected to your ESP3D*///#define SD_DEVICE_CONNECTION ESP_NOT_SHARED_SD
/* SD card library* ESP_SD_NATIVE //esp32 / esp8266* ESP_SDIO //esp32 only* ESP_SDFAT2 //esp8266 / esp32*///#define SD_DEVICE ESP_SDFAT2
/* Sdio bit mode* Mode used by SDIO library 1 bit / 4bits* SD_ONE_BIT_MODE* SD_FOUR_BIT_MODE*///#define SDIO_BIT_MODE SD_ONE_BIT_MODE
/* Enable date/time on files* Set date/time on files using SNTP or last webui connection*///#define SD_TIMESTAMP_FEATURE
/************************************** SD card pins*************************************/
/* SD card detect pin* The pin used to detect SD card*///#define ESP_SD_DETECT_PIN 4
/* SD card detect pin value* State of SD card detect pin when card is present*///#define ESP_SD_DETECT_VALUE 0
/* SD shared flag pin* The pin used to enable SD card for ESP board*///#define ESP_FLAG_SHARED_SD_PIN -1
/* SD shared flag pin value* State of SD card shared pin for ESP board*///#define ESP_FLAG_SHARED_SD_VALUE 0
/* SD card CS pin* The pin used to select SD card in SPI mode*///#define ESP_SD_CS_PIN 5
/************************************** Remote access** Remote filesystem access*************************************/
/* Enable global filesystem* Allows to access to all filesystems from same location*///#define GLOBAL_FILESYSTEM_FEATURE
/* WebDav access* Use WebDav to access to your filesystem* FS_ROOT //mount all FS, need GLOBAL_FILESYSTEM_FEATURE* FS_FLASH //mount Flash FS* FS_SD mount SD FS*///#define WEBDAV_FEATURE FS_ROOT
/* FTP access* Use FTP to access to your filesystem (1 connection only)* FS_ROOT //mount all FS, need GLOBAL_FILESYSTEM_FEATURE* FS_FLASH //mount Flash FS* FS_SD //mount SD FS*///#define FTP_FEATURE FS_ROOT/************************************** Reset ESP3D** Reset ESP3D settings*************************************/
/* Enable pin reset feature* Use a pin to reset ESP3D settings*///#define PIN_RESET_FEATURE
/* Reset pin* The pin used to reset ESP3D setting if set to low for more than 1 second at start*/#define ESP3D_RESET_PIN 0/************************************** Update ESP3D** Update ESP3D firmware*************************************/
/* Enable OTA* Over The Air Update (OTA)*///#define OTA_FEATURE
/* Enable Web Update* Update firmware using WebUI, need 4MB of flash*/#define WEB_UPDATE_FEATURE
/* Enable SD card Update* Update firmware and settings using file on SDCard*///#define SD_UPDATE_FEATURE/************************************** Display settings** Rendering screens*************************************/
/* Printer screen* If your printer has a display*/#define PRINTER_HAS_DISPLAY
/* ESP3D screen* Screen connected to ESP board* OLED I2C SSD1306 128X64* OLED_I2C_SSDSH1106_132X64* TFT_SPI_ST7789_240X240* TFT_SPI_ST7789_135X240*///#define DISPLAY_DEVICE OLED_I2C_SSD1306_128X64
/* Flip screen* Flip/rotate screen*///#define DISPLAY_FLIP_VERTICALY
/* Display i2C address* Wire address of display*///#define DISPLAY_I2C_ADDR 0x3c
/* Display reset pin* The pin used to reset the screen (optional)*///#define DISPLAY_I2C_PIN_RST 22
/* TFT led pin* The pin used for the backlight*///#define DISPLAY_LED_PIN -1/************************************** Audio settings** Buzzer feature*************************************/
/* Enable buzzer* Your esp board has a passive buzzer*///#define BUZZER_DEVICE
/* Buzzer pin* The pin used for the passive buzzer*///#define ESP3D_BUZZER_PIN 33/************************************** Sensor settings** Sensor feature*************************************//* Sensor pin* The pin used for the sensor*///#define ESP3D_SENSOR_PIN 34
/* Sensor Unit* Unit of the sensor result*///#define SENSOR__UNIT "C"/************************************** Camera settings** Connected camera*************************************/
/* Camera type* CAMERA_MODEL_CUSTOM //Edit the pins in include/pins.h* CAMERA_MODEL_ESP_EYE* CAMERA_MODEL_M5STACK_PSRAM* CAMERA_MODEL_M5STACK_V2_PSRAM* CAMERA_MODEL_M5STACK_WIDE* CAMERA_MODEL_AI_THINKER //ESP32-CAM* CAMERA_MODEL_WROVER_KIT* CAMERA_MODEL_ESP32_CAM_BOARD* CAMERA_MODEL_ESP32S2_CAM_BOARD* CAMERA_MODEL_ESP32S3_CAM_LCD* CAMERA_MODEL_ESP32S3_EYE* Camera connected to ESP board, only ones with PSRAM are supported*///#define CAMERA_DEVICE CAMERA_MODEL_AI_THINKER
/* Flip vertically* Flip camera vertically*///#define CAMERA_DEVICE_FLIP_VERTICALY/************************************** Levels of security** How commands are allowed to be sent to ESP3D*************************************/
/* Enable serial commands* Allow commands to be sent to ESP3D via serial port*/#define SERIAL_COMMAND_FEATURE
/* Allow remote access by enabling cross origin access* check https://developer.mozilla.org/en-US/docs/Web/HTTP/CORS* this should be enabled only in specific cases* like show the camera in web page different than device web server* /if you do not know what is that then better left it commented* Allow to show the camera in web page different than device web server*///#define ESP_ACCESS_CONTROL_ALLOW_ORIGIN
/* Enable authentication* Force usage of authentication for commands*///#define AUTHENTICATION_FEATURE/************************************** Additional features** Extra settings*************************************/
/* Enable direct control pin* Controls pins using [ESP201]*/#define DIRECT_PIN_FEATURE/************************************** Scripting settings** Scripting on ESP3D*************************************//* Enable Autostart* Commands to run on startup* Separate commands with ';' or use file*///#define ESP_AUTOSTART_SCRIPT "M117 Mounting SD;M21"//#define ESP_AUTOSTART_SCRIPT_FILE "autoscript.gco"
/* Enable lua interpreter* Allow to use lua interpreter on ESP3D*///#define ESP_LUA_INTERPRETER_FEATURE
/* Gcode Host Feature* This feature allows to process Gcode files like macros.*/#define GCODE_HOST_FEATURE